Advantech SBD75e Series Especificaciones Pagina 62
- Pagina / 97
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Web GUI Monitoring & Control
4.8.8 User-1
This enables a specific user mode where specific PIDs are decrypted. The SI information is not
altered so this mode is not BISS compliant. The actual PIDs to be decrypted are specified only on
the command line. A 12 digit hex value is required for the session word. The even key is the same
key as used for BISS-1.
This mode is used to guarantee that the decrypted transport stream will match the original.
4.8.9 User-E
This is identical to the User-1 mode except a 16 digit hex value is required for the ESW and a 14
digit hex value is required for the injected ID. The even key is the same key as used for BISS-E.
4.8.10 BISS Insertion Period
This sets the frequency that the Program Association Table (PAT), Programme Map Table (PMT)
and Conditional Access Table (CAT) will be inserted into the stream. The default is 200 ms and this
value should be suitable in most circumstances.
Table 4.3: BISS Status
Property Status Description
State
Uninitialized Error condition, BISS failure
Idle : illegal in
this mode
BISS cannot be used in this mode
Idle BISS is turned off
Configured BISS is active, this will include BISS-0 Mode
Extraction
Active SI extraction is active
Inactive no SI extraction
Keys
OK Valid keys present, this should always be OK
stream info PAT not found The PAT is not detected, critical failure
Corrupted tables At least one of the PMT listed in the PAT cannot be extracted or
At least one of the PMT has a bad structure or a CRC error
No CAT
detected
CAT is not found, this can be normal
OK Transport stream is OK
processing
Ciphering The block cipher is engaged and ciphering
Unciphering The block cipher is engaged and deciphering
None The block cipher is not engaged
PMT info
Too many
PMT(s)
too many PMT(s) are received for the playout RAM (overflow)
Incorrect PMT(s)
A PMT cannot be modified to add/remove BISS SI (PIDs listed in the PMT
would not be ciphered/deciphered)
Missing PMT(s) A PMT listed in the PAT could not be retrieved
OK All is OK
4-26 SBD75e Series Demodulator Installation and Operation Manual
- SBD75e Series Demodulator 1
- Preface 2
- Copyright Notice 3
- Customer Support 3
- Warranty and Service 4
- Safety Notices 5
- Contents 6
- Who Should Use This Manual 8
- Version Information 8
- RF Interface Options 8
- Summary of Features 9
- Guided Tour 9
- 1.3.2.2 LED Indicators 10
- 1.3.2.3 Keypad 11
- Rear Panel 12
- Typical System Setup 13
- Getting Started 14
- Installation 15
- Introduction 16
- Moving the Equipment Safely 17
- Unpacking 17
- Mechanical Inspection 17
- Installing the Equipment 18
- Cable Routing 19
- Equipment Access 19
- Ventilation 19
- Power Cables 20
- AC Power and Fuse 21
- M&C Connector - RS232 23
- Alarms Connector 24
- RF (L-Band) Input Connector 24
- ASI Output Connector 24
- Demodulator Acquisition Tips 25
- BER Measurement 26
- Overview 29
- Select Board 29
- 3.3.2.1 Status 30
- 3.3.2.1.1 Status 30
- 3.3.2.2 Configure 31
- 3.3.2.2.1 Profiles 31
- 3.3.2.2.2 Inputs 33
- 3.3.2.2.3 Coding 33
- Table 3.9: Coding Options 34
- List of Contents 37
- List of Figures 38
- List of Tables 38
- Safari (Version 2.0) 39
- Opera (Version 9.0) 39
- Accessing the GUI 39
- Overview: Information 40
- Overview: Alarms 40
- Overview: Status 42
- Information 43
- SBD75e: Status 45
- SBD75e: Alarms 46
- General 47
- Output Alarms 48
- Setting Alarms 49
- Setting Warnings 49
- Alarm Status 49
- Play/Pause 50
- Analyzer Pane format 51
- Analyzer Information Icons 51
- 4.7.3.1.2 Cursors 52
- 4.7.3.2.1 Number of Points 53
- 4.7.3.2.2 Persistence 53
- SBD75e: BISS Decryption 58
- BISS Mode Selection 59
- 4.8.2 Off 60
- 4.8.3 BISS-0 60
- 4.8.4 BISS-1 60
- Odd/Even-1 61
- Odd/Even-E 61
- BISS Insertion Period 62
- SBD75e: Configuration 63
- LNB power supply options 64
- PL scrambling seed 64
- Stream Isolation 64
- MODCOD filter 64
- ISI Assignment 64
- 4.9.2.1 Automatic Mode 65
- 4.9.2.3 Manual Mode 68
- 4.9.2.3.1 MODCOD Filter 69
- Advanced 72
- 4.9.3.1 Padding Support 73
- 4.9.3.2 VCM Guard Mode 73
- Profiles 74
- To clone a profile: 76
- Technical Specification 81
- Standards Compliance 84
- Glossary 86
© 2020, manymanuals.es. Todos los derechos reservados | 0.146 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales