Advantech PCM-5864L Manual de usuario Pagina 46
- Pagina / 141
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
34 PCM-5864/E/L User's Manual
2.18.6 LCD backlight signal setting (J8)
The backlight signal can either choose positive enable or negative
enable when using the J8 setting.
Table 2-20: LCD backlight signal setting (J8)
Positive signal Negative signal
J8
Configuration of the VGA interface is done completely via the
software utility. You do not have to set any jumpers. Refer to
Chapter 3 for software setup details.
Refer to Chapter 3 for details on connecting the five standard
LCDs: Sharp LM64183P, LM64P89, Toshiba LTM10C042, Sharp
64C142, and Planar EL display.
2.19 Ethernet configuration
The PCM-5864/E/L is equipped with a high performance 32-bit
PCI-bus Ethernet interface which is fully compliant with IEEE
802.3U 10/100Mbps CSMA/CD standards. It is supported by all
major network operating systems.
The medium type can be configured via the RSET8139.EXE
program included on the utility disk. (See Chapter 3 for detailed
information.)
2.19.1 100Base-T connector (CN3)
100Base-T connects to the PCM-5864/E/L via an adapter cable to
a 10-pin polarized header (CN3). For 10Base-T RJ-45 operation,
an adapter cable converting CN3 into a standard RJ-45 jack is
required.
1
2
3
1
2
3
- PCM-5864/E/L 1
- Copyright Notice 2
- Packing list 3
- Contents 4
- General Information 13
- 1.1 Introduction 14
- 1.2 Features 15
- 1.3 Specifications 16
- Installation 21
- 2.1 Jumpers 22
- 2.2 Connectors 23
- 2.3 Locating jumpers 24
- 2.4 Locating connectors 25
- 2.4.2 Solder side 26
- 2.5 Setting jumpers 27
- Chapter 2 Installation 17 29
- 1.5 /3.5 2* 2.5 3 4 30
- 4.5 5 5.5 (reserved) 30
- *33 MHz CPU CLK/2 30
- 1 2 3 1 2 3 30
- * default setting 31
- 2.6.4 CMOS clear (J7) 32
- 2.7.1 Installing DIMMs 33
- 2.8.2 CompactFlash (CN501) 34
- Chapter 2 Installation 23 35
- 2.12.1 Speaker 37
- 2.12.2 LED interface 37
- 2.12.3 Watchdog output 37
- 2.12.4 Reset switch 37
- Chapter 2 Installation 27 39
- 2.15 IR connector (CN17) 40
- CN502) (PCM-5864/E only) 40
- J21) 41
- *RS-232 RS-422 RS-485 42
- Port Address range Interrupt 42
- *5 V 3.3 V 45
- SHFCLK* ASHFCLK 45
- 2.19 Ethernet configuration 46
- 2.19.2 Network boot 47
- 2.21 USB connectors (CN16) 48
- (PCM-5864 only) 49
- Software 51
- Configuration 51
- 3.1 Introduction 52
- (640 x 480 AD4 EL) 53
- LTM10C042 PCM-5864/E/L CN15 54
- Pin Name Pin Name 54
- LM64C142 PCM-5864/E/L CN15 55
- LTM12C275A PCM-5864/E/L CN15 56
- Award BIOS Setup 59
- 4.2 AWARD BIOS setup 61
- 4.2.2 Standard CMOS setup 62
- 4.2.3 BIOS features setup 63
- 4.2.4 Chipset features setup 64
- 4.2.5 Power management setup 65
- 4.2.6 PnP/PCI configuration 66
- 4.2.7 Integrated peripherals 67
- 4.2.8 Load BIOS defaults 68
- 4.2.9 Change password 69
- 4.2.10 Auto detect hard disk 70
- 4.2.11 Save & exit setup 70
- 4.2.12 Exit without saving 70
- PCI SVGA Setup 71
- 5.1 Before you begin 72
- 5.2 Introduction 72
- 5.2.2 Display memory 73
- 5.2.3 Display types 73
- D:\VGA\Win95\ 74
- Chapter 5 PCI SVGA Setup 63 75
- Chapter 5 PCI SVGA Setup 65 77
- ChipsCPL 78
- Chapter 5 PCI SVGA Setup 67 79
- D:\VGA\NT40\ 80
- Chapter 5 PCI SVGA Setup 69 81
- 5.4 Further information 82
- • Introduction 83
- Windows 95/98 83
- 6.1 Introduction 84
- Chapter 6 Video 73 85
- Chapter 6 Video 75 87
- Windows 95/98/NT 89
- 7.1 Introduction 90
- Chapter 7 Audio 79 91
- PCI Bus Ethernet 93
- Interface 93
- 8.1 Introduction 94
- 8.3 Further information 99
- Programming the 101
- Watchdog Timer 101
- Installing PC/104 105
- B.1 Installing PC/104 modules 106
- Pin Assignments 109
- CPU fan power connector (CN1) 110
- Pin Signal 111
- Speaker out connector (CN502) 112
- Audio connector (CN4) 112
- Aux line-in connector (CN7) 113
- Main power connector (CN8) 114
- * low active 116
- PC/104 connectors (CN11) 117
- IDE HDD connector (CN12) 118
- Front panel connector (CN15) 121
- USB connector (CN16) 121
- IR connector (CN17) 122
- CRT display connector (CN18) 122
- Video-out connector (CN19) 123
- Flat panel connector (CN20) 124
- Pin Signal Pin Signal 125
- COM port connector (CN23) 126
- Pin Signal Signal Signal 127
- LVDS connector (JP3) 130
- Assignments 131
- D.1 System I/O ports 132
- D.2 1st MB memory map 133
- D.3 DMA channel assignments 133
- D.4 Interrupt assignments 134
- Optional Extras 135
- E.1 PCM-10586-3 cable kit for 136
- PCM-5864/E/L 136
- E.3 Optional USB cable (CN16) 137
- Mechanical 138
- Drawings 138
- F.1 Component side 139
- F.2 Solder side 140
Relacionado con productos y manuales para Barebones Pc / Estación De Trabajo Advantech PCM-5864L
(62 paginas)
(28 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.017 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales