Advantech PCM-5864L Manual de usuario Pagina 41
- Pagina / 141
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 2 Installation 29
2.16.5 Audio power source setting (J23)
The PCM-5864/E/L is designed to work with a single +5 V power
supply. The audio interface can also function normally under
single +5V power supply, but most audio controllers require an
independent power source generated from a +12 V power supply.
The independent power source avoids the noise from the other
digital circuits. The PCM-5864‘s audio interface can accept +12 V
power to provide improved quality audio. This is done via J23.
Table 2-11: Audio power source setting
*+5 V +12 V
J23
* default setting
Configuration of the audio interface is done entirely via the
software utility. You do not have to set any jumpers. Refer to
Chapter 6 for audio setup details.
2.17 COM port connector (CN23)
The PCM-5864/E/L provides four serial ports (COM1, 3, 4:
RS-232; COM2: RS-232/422/485) in one COM port connector.
The COM port connector is a 40-pin, dual-inline, male header. It
provides connections for serial devices (a mouse, etc.) or a
communication network. You can find the pin assignments for the
COM port connector in Appendix C.
2.17.1 COM2 RS-232/422/485 setting (J19, J20,
J21)
COM2 can be configured to operate in RS-232, RS-422, or RS-
485 mode. This is done via J19 and J20.
123 1 23
- PCM-5864/E/L 1
- Copyright Notice 2
- Packing list 3
- Contents 4
- General Information 13
- 1.1 Introduction 14
- 1.2 Features 15
- 1.3 Specifications 16
- Installation 21
- 2.1 Jumpers 22
- 2.2 Connectors 23
- 2.3 Locating jumpers 24
- 2.4 Locating connectors 25
- 2.4.2 Solder side 26
- 2.5 Setting jumpers 27
- Chapter 2 Installation 17 29
- 1.5 /3.5 2* 2.5 3 4 30
- 4.5 5 5.5 (reserved) 30
- *33 MHz CPU CLK/2 30
- 1 2 3 1 2 3 30
- * default setting 31
- 2.6.4 CMOS clear (J7) 32
- 2.7.1 Installing DIMMs 33
- 2.8.2 CompactFlash (CN501) 34
- Chapter 2 Installation 23 35
- 2.12.1 Speaker 37
- 2.12.2 LED interface 37
- 2.12.3 Watchdog output 37
- 2.12.4 Reset switch 37
- Chapter 2 Installation 27 39
- 2.15 IR connector (CN17) 40
- CN502) (PCM-5864/E only) 40
- J21) 41
- *RS-232 RS-422 RS-485 42
- Port Address range Interrupt 42
- *5 V 3.3 V 45
- SHFCLK* ASHFCLK 45
- 2.19 Ethernet configuration 46
- 2.19.2 Network boot 47
- 2.21 USB connectors (CN16) 48
- (PCM-5864 only) 49
- Software 51
- Configuration 51
- 3.1 Introduction 52
- (640 x 480 AD4 EL) 53
- LTM10C042 PCM-5864/E/L CN15 54
- Pin Name Pin Name 54
- LM64C142 PCM-5864/E/L CN15 55
- LTM12C275A PCM-5864/E/L CN15 56
- Award BIOS Setup 59
- 4.2 AWARD BIOS setup 61
- 4.2.2 Standard CMOS setup 62
- 4.2.3 BIOS features setup 63
- 4.2.4 Chipset features setup 64
- 4.2.5 Power management setup 65
- 4.2.6 PnP/PCI configuration 66
- 4.2.7 Integrated peripherals 67
- 4.2.8 Load BIOS defaults 68
- 4.2.9 Change password 69
- 4.2.10 Auto detect hard disk 70
- 4.2.11 Save & exit setup 70
- 4.2.12 Exit without saving 70
- PCI SVGA Setup 71
- 5.1 Before you begin 72
- 5.2 Introduction 72
- 5.2.2 Display memory 73
- 5.2.3 Display types 73
- D:\VGA\Win95\ 74
- Chapter 5 PCI SVGA Setup 63 75
- Chapter 5 PCI SVGA Setup 65 77
- ChipsCPL 78
- Chapter 5 PCI SVGA Setup 67 79
- D:\VGA\NT40\ 80
- Chapter 5 PCI SVGA Setup 69 81
- 5.4 Further information 82
- • Introduction 83
- Windows 95/98 83
- 6.1 Introduction 84
- Chapter 6 Video 73 85
- Chapter 6 Video 75 87
- Windows 95/98/NT 89
- 7.1 Introduction 90
- Chapter 7 Audio 79 91
- PCI Bus Ethernet 93
- Interface 93
- 8.1 Introduction 94
- 8.3 Further information 99
- Programming the 101
- Watchdog Timer 101
- Installing PC/104 105
- B.1 Installing PC/104 modules 106
- Pin Assignments 109
- CPU fan power connector (CN1) 110
- Pin Signal 111
- Speaker out connector (CN502) 112
- Audio connector (CN4) 112
- Aux line-in connector (CN7) 113
- Main power connector (CN8) 114
- * low active 116
- PC/104 connectors (CN11) 117
- IDE HDD connector (CN12) 118
- Front panel connector (CN15) 121
- USB connector (CN16) 121
- IR connector (CN17) 122
- CRT display connector (CN18) 122
- Video-out connector (CN19) 123
- Flat panel connector (CN20) 124
- Pin Signal Pin Signal 125
- COM port connector (CN23) 126
- Pin Signal Signal Signal 127
- LVDS connector (JP3) 130
- Assignments 131
- D.1 System I/O ports 132
- D.2 1st MB memory map 133
- D.3 DMA channel assignments 133
- D.4 Interrupt assignments 134
- Optional Extras 135
- E.1 PCM-10586-3 cable kit for 136
- PCM-5864/E/L 136
- E.3 Optional USB cable (CN16) 137
- Mechanical 138
- Drawings 138
- F.1 Component side 139
- F.2 Solder side 140
Relacionado con productos y manuales para Barebones Pc / Estación De Trabajo Advantech PCM-5864L
(62 paginas)
(28 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.143 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales