Advantech PPC-S123 Manual de usuario

PPC-123Pentium® III processor-basedpanel PC with 12.1" LCD flat paneldisplayUser’s Manual

5.5 Internal -12 V source selection setting (JP1) ... 565.6 VGA Interface ... 575.6.1 LCD p

84PPC-123 User's Manual9.1 Award BIOS SetupThe PPC-123 comes with an Award BIOS chip that contains the ROMsetup for your system. This chip serve

Chapter 9 Award BIOS Setup85A setup program, built into the system BIOS, is stored in the CMOSRAM that allows the configuration settings to be change

86PPC-123 User's Manual9.3.1 Hard Disk ConfigurationsTYPESelect from 1 to 45 to fill the remaining fields with predefined values fordisk drives.

Chapter 9 Award BIOS Setup879.4 BIOS Features SetupFigure 9-3: BIOS features setup screenMoving around the BIOS Features and Chipset Features setuppr

88PPC-123 User's ManualExternal CacheWhen enabled, supports an external cache SRAM.The options are: Enabled (Default), Disabled.CPU L2 Cache ECC

Chapter 9 Award BIOS Setup89Swap Floppy DriveWhen enabled, allows you to switch the order in which the operatingsystem accesses the floppy drives dur

90PPC-123 User's ManualThe options are: Disabled (Default), Enabled.PCI/VGA Palette SnoopWhen enabled, allows you to install an enhanced graphic

Chapter 9 Award BIOS Setup919.5 Chipset Features SetupNote: It is strongly recommended that setup items in thissection NOT be changed, because advanc

92PPC-123 User's ManualSDRAM Data Integrity ModeWhen set as Non-ECC, supports standard 64-bit DIMM RAMmodules. When set as ECC, supports standar

Chapter 9 Award BIOS Setup93Delayed TransactionWhen disabled, the syatem operates normally. When enabled, thesystem can support lower-speed ISA devic

9.3 Standard CMOS Setup ... 859.3.1 Hard Disk Configurations ... 869

94PPC-123 User's ManualPM Control by APMThe option "No" allows the BIOS to ignore the APM (AdvancedPower Management) specification. Se

Chapter 9 Award BIOS Setup95Standby ModeThe system will not enter Standby mode, because this option isdesignated as "Disabled".Suspend Mode

96PPC-123 User's Manual9.7 PNP/PCI Configuration SetupFigure 9-6: PNP/PCI configuration setup screenPNP OS InstalledSelect Yes if the installed

Chapter 9 Award BIOS Setup97The options are: Disabled (Default), Enabled.Used MEM base addrChoose and use the MEM base address.The options are: N/A (

98PPC-123 User's Manual9.10 Integrated PeripheralsFigure 9-8: Integrated peripherals screenIDE HDD Block ModeThis allows your hard disk controll

Chapter 9 Award BIOS Setup99Your system supports five modes, numbered from 0 through 4, whichdiffer primarily in timing. When "Auto" is sel

100PPC-123 User's ManualThe options are: 378/IRQ7 (Default), 3BC/IRQ7, 278/IRQ5, Disabled.Parallel Port ModeYou can choose different data transf

Chapter 9 Award BIOS Setup1019.12 IDE HDD Auto DetectionFigure 9-9: IDE HDD auto detection screenThe IDE Hard Disk Drive Auto Detection feature autom

102PPC-123 User's Manual9.13 Save and Exit SetupFigure 9-10: Save and exit setup screenAfter you have made changes in the BIOS setup, press &quo

PCMCIA• Introduction• Installation of PCMCIA Driver- for Windows 9510CHAPTER

Appendix B Programming the Watchdog Timer 127B.1 Programming the Watchdog Timer ... 128Appendix C Full Disassembly Procedures 131C.

104PPC-123 User's Manual10.1 IntroductionThe PPC-123 is equipped with a high performance PCMCIA interfacewhich complies with the 1995 PCMCIA car

Chapter 10 PCMCIA10510.2.1 Installation for Windows 95a. In "Start", "Run",type the path: D:\PPC123&153\Cardbus\win95osr2\Set

106PPC-123 User's Manual

Touchscreen• Introduction• Installation of Driverfor Resistive Touchscreen- for Windows 95- for Windows 98- for Windows NT- for Windows 2000- for Win

108PPC-123 User's Manual11.1 Introduction11.1.1 General informationThe PPC-123's optional touchscreen incorporates advancedsecond-generatio

Chapter 11 Touchscreen109the following chemicals when exposed for a period of one hour at atemperature of 21° C (71° F):- Acetone- Methylene chloride

110PPC-123 User's Manual11.2.1 Installation for Windows 953.4.a.Click the "Yes"buttom to restartyour computer.2.a.Click "Yes"

Chapter 11 Touchscreen1115.a.Touch targets tocalibrate thetouchscreencontroller.End

112PPC-123 User's Manual11.2.2 Installation for Windows 98If you want to use the touchscreen driver CD-ROM accompanyingyour panel PC, refer to t

Chapter 11 Touchscreen1135.a.Touch targets tocalibrate thetouchscreencontroller.End

FiguresFigure 1-1: The panel PC in perspective ...3Figure 1-2: How to read the PPC-123 manual ...

114PPC-123 User's Manual3.4.a. Choose a suitableitem.2.a. Press the "Next"button.1.a.Select "Start","Run".Type the

Chapter 11 Touchscreen1155.a.Chose COM4.6.a. Click "OK" toreboot the System.b. Press "OK".7.a. Calibrate thetouchscreen.End

116PPC-123 User's Manual11.2.4 Intallation for Windows 20003.2.a.Press "Next"a. Click "Yes"1.a.Select "Start",&qu

Chapter 11 Touchscreen1177.6.a.Press "Finish"a.Click "Yes" toreboot the system5.a.Choose "COM4"Then click "Next&q

118PPC-123 User's Manual9.a.Click "Finish" tocompleteinstallationEnd

Chapter 11 Touchscreen1194.a. Press "Next"1.a. Select "Start","Run"Type the path"D:\123&153\Elotouch\WInME\Set

120PPC-123 User's Manual5.a. Choose "COM4"b. Press "Next"6.a.Calibrate thetouch screen7.a. Click "Finish" tocomple

Chapter 11 Touchscreen12111.3 Installation of Driver for CapacitiveTouchscreenTo facilitate installation of the touchscreen driver, you should read t

122PPC-123 User's Manuala. Select "Start", "Run".b.Type in: D:\PPC123&153\Microtouch\Tware54\Setup.exe1.a.Follow theinst

Chapter 11 Touchscreen123a.Select the "ExpressInstall..." item..b. Click on "Next".5.a. Select the "Yes, ..."item to re

Figure C-1: Disassembly steps 1 - 4 ... 133Figure C-2: Disassembly steps 5 - 6 ...

124PPC-123 User's Manual

LCD Specifications andSelection SettingsAPPENDIXA

126PPC-123 User's ManualA.1 PPC-123 LCD SpecificationsDisplay type: 12.1” TFT LCDMax. resolution: 800 x 600Colors: 256 KDot size (mm): 0.33 x 0

Programming theWatchdog TimerThe PPC-123 is equipped with a watch-dog timer that resets the CPU or generatesan interrupt if processing comes to astand

128PPC-123 User's ManualB.1 Programming the Watchdog TimerTo program the watchdog timer, you must write a program whichwrites I/O port address 4

Appendix B Programming the Watchdog Timer129The following example shows how you might program the watchdogtimer in BASIC:10 REM Watchdog timer examp

130PPC-123 User's Manual

Full DisassemblyProceduresAPPENDIXC

132PPC-123 User’s ManualC.1 Full Disassembly ProceduresIf you want to completely disassemble the panel PC, follow thestep-by-step procedures below. U

Appendix C Full Disassembly Procedures133Figure C-1: Disassembly steps 1 - 4Step 1&Step 2Step 4Step 3

TablesTable 5-1: Jumpers and their functions ... 49Table 5-2: Panel PC connectors ...

134PPC-123 User’s Manualmachine. The electric fan and power inlet can also be removedfrom the case by unscrewing the screws.5. Unscrew the fourteen s

Appendix C Full Disassembly Procedures135Figure C-2: Disassembly steps 5 - 6Step 5Step 6I/O bracketEMIprotectioncoverMotherboard

136PPC-123 User’s Manual7. Unscrew the four screws on the power supply board. The powersupply board can be detached from the LCD holding plate afteru

Appendix C Full Disassembly Procedures137Figure C-3: Disassembly steps 7 - 11Step 11Step 8Step 9Step 10Backplane plateLCDPowersupplyStep 7Front panel

138PPC-123 User’s Manual

Pin Assignments• AT Power Connector (J1)• TV Output Connector (J2) (*Reserved)• Inverter Power Connector (J4)• Internal Speaker Connector (J6)• Front

140PPC-123 User’s ManualD.1 AT Power Connector (J1)Table D-1: AT power connector (J1)Pin Signal1 PS_NO #2 +5 VSB3 +12 V4 -12 V5 GND6 GND7 GND8 GND9 -

Appendix D Pin Assignments141D.3 Inverter Power Connector (J4)Table D-3: Inverter power connector (J4)Pin Signal1 +12 V2 GND3 ENABKL4 Brightness Adj.

142PPC-123 User’s ManualTable D-5: Front panel control connector (J8) (*Reserved)Pin Signal1 Vcc2 GND3 HDD LED4 Reset SW5 Power SW6NCD.5 Front Panel

Appendix D Pin Assignments143Table D-7: Flat panel display connector (CN2)Pin Signal Pin Signal1 VDDSAFE5 2 VDDSAFE53 GND 4 GND5 VDDSAFE3 6 VDDSAFE37

144PPC-123 User’s ManualTable D-8: Flat panel display connector (CN3)Pin Signal Pin Signal1 VDDSAFE5 2 VDDSAFE53 GND 4 GND5 VDDSAFE3 6 VDDSAFE37 Vcon

Appendix D Pin Assignments145D.9 Panel Link Interface (CN4) (*Reserved)Table D-9: PanelLink Interface (CN4) (*Reserved)Pin Signal Pin Signal1 TXC- 11

146PPC-123 User’s ManualD.10 Floppy Drive Connector (CN10)Table D-10: Floppy drive connector (CN10)Pin Signal Pin Signal1VCC (+5 V) 14 STEP2 INDEX 15

Appendix D Pin Assignments147D.11 EIDE Hard Disk Drive Connector (CN16)Table D-11: EIDE hard disk drive connector (CN16)Pin Signal Pin Signal1 IDE RE

148PPC-123 User’s ManualD.12 CD-ROM Connector (CN18)Table D-12: CD-ROM connector (CN18)Pin Signal Pin Signal1 Audio_L 2 Audio_R3 GND 4 GND5 IDE RESET

Appendix D Pin Assignments149D.13 CPU Fan Power Connector (FAN1)Table D-13: CPU fan power connector (FAN1)Pin Signal1 GND2 +12 V3 FAN_DETD.14 System

150PPC-123 User’s ManualD.15 PCI/ISA Bus Expansion Connector(SLOT1)side viewB1E1A1F1B2E2A2F2B3E3A3F3B4E4A4F4B5E5A5F5B6A6B8E8A8F8B7E7A7F7B9E9A9F9B10E1

Appendix D Pin Assignments151Table D-15: PCI/ISA slot pin assignments (Pins A and B)Pin Signal Pin SignalA1 IOCHK B1 GNDA2 SD7 B2 RSTA3 SD6 B3 VCCA4

152PPC-123 User’s ManualTable D-16: PCI/ISA slot pin assignments (Pins C and D)Pin Signal Pin SignalC1 SBHE D1 MEM16C2 LA23 D2 IO16C3 LA22 D3 IRQ10C4

Appendix D Pin Assignments153Table D-17: PCI/ISA slot pin assignments (Pins E and F)Pin Signal Pin SignalE1 GND F1 GNDE2 GND F2 GNDE3 INT 1 F3 INT3E4

General InformationThis chapter gives backgroundinformation on the PPC-123 panel PC.• Introduction• How to Use This Manual• Specifications• Dimensions

154PPC-123 User’s ManualTable D-18: PCI/ISA slot pin assignments (Pins G and H)Pin Signal Pin SignalG1 --- H1 SERRG2 --- H2 AD15G3 CBE1 H3 AD14G4 PAR

Appendix D Pin Assignments155Table D-19: Internal COM4 and PS/2 Connector (CN23)Pin Signal Pin Signal1 NRLSD 2 NDSR3 NRX 4 NRTS5 NTX 6 NCTS7 NDTR 8 N

156PPC-123 User’s Manual

Mounting Instructions• Introduction• Panel Mounting• Desktop Stand Mounting• Swingarm Stand MountingAPPENDIXE

158PPC-123 User’s ManualE.1 IntroductionThe PPC-123 can be placed as is on a shelf or table, mounted into apanel, or mounted on a customized swingarm

Appendix E Mounting Instructions159E.2.2 Installation procedureTo mount the PPC-123 into a panel:1. There are six plastic caps located along the fou

160PPC-123 User’s ManualE.3 Desktop Stand MountingThe PPC-123 has a customized stand suitable for desktops and otherhorizontal locations. A unique sp

Appendix E Mounting Instructions161Figure E-3: Desktop stand mountingRear coverof panel PCMain bodyHolding plateBaseTop coverCapRear cover

162PPC-123 User’s ManualE.4 Swingarm Stand MountingThe PPC-123 can be mounted on a unique swingarm. This versatileaccessory is easy to install and op

2PPC-123 User's Manual1.1 IntroductionThe PPC-123 panel PC is a multimedia Pentium® III processor-basedcomputer that is designed to serve as a h

Chapter 1 General Information3Figure 1-1: The panel PC in perspectiveCRT MonitorNetworkSpeakersKeyboardMouseJoystickPrinterFaxmodemTouchscreen

Copyright noticeThis document is copyrighted 2001, by Advantech Co., Ltd. All rightsare reserved. Advantech Co., Ltd. reserves the right to alter thep

4PPC-123 User's Manual1.2 How to Use This ManualThis manual contains all the information you need to set up anduse the panel PC. In addition to

Chapter 1 General Information5PC.Appendix D includes all pin assignments on the connectors.Appendix E helps users install the panel PC, which is mou

6PPC-123 User's Manual1.3 SpecificationsGeneral• Dimensions (W x H x D): 375 x 285 x 93.3 mm (14.7" x 11.2" x 3.7")• Weight: 5.2

Chapter 1 General Information7•Floppy disk drive: Supports up to two FDDs (720 KB / 1.44 MB).One built-in FDD included inside FDD housing.• Parallel

8PPC-123 User's Manual• Audio interface: Microphone-in, Line-in, Line-out and Gameports (MPU-401)PCI bus Ethernet interface• Chipset: Realtek RT

Chapter 1 General Information9Note: The panel PC with the optionally installed touch-screen will share COM4. Once the touchscreen isinstalled, COM4

10PPC-123 User's Manual1.4 DimensionsFigure 1-3: Dimensions of the PPC-123Unit: mm

System Setup• A Quick Tour of the Panel PC• Preparing for First-time Usage• Running the Setup Program• Installing the System Software• Installing the

12PPC-123 User's Manual2.1 A Quick Tour of the Panel PCBefore you start to set up the panel PC, take a moment to becomefamiliar with the locatio

Chapter 2 System Setup13When you look at the left side of the panel PC, you will see the floppydisk drive, CD-ROM drive and PCMCIA expansion sockets,

Packing ListBefore installing your panel PC, ensure that the following materialshave been received:• PPC-123 series panel PC• User's manual• Acce

14PPC-123 User's ManualFigure 2-3: Rear view of the panel PCFigure 2-4 shows the I/O section and power switch of the panel PC.Figure 2-4: Tilted

Chapter 2 System Setup152.2 Preparing For First-time UseBefore you start to set up the panel PC system, you should have atleast the following items r

16PPC-123 User's Manual2.3.2 Installing the DC power insulator with hoodThe panel PC can also be powered by DC electrical outlet (24 VDC or 12VD

Chapter 2 System Setup17frame ground ( G ), and pin 3 should be plugged into the negative DCpower input ( - ).STEP 3: Mount the front part of the mal

18PPC-123 User's ManualSTEP 5: Attach the upper cap to the bottom tray and secure it with thescrews.STEP 6: Now that you have completed the asse

Chapter 2 System Setup192.3.3 Connecting the keyboard and mouse1. Connect the Y-shaped adapter to the PS/2 mouse and keyboardport on the I/O section

20PPC-123 User's Manual2.4 Running the BIOS Setup ProgramYour panel PC is likely to have been properly set up and configured byyour dealer prior

Chapter 2 System Setup212.5 Installing System SoftwareRecent releases of operating systems from major vendors includesetup programs which load automa

22PPC-123 User's Manual2.6 Installing the DriversAfter installing your system software, you will be able to set up theEthernet, SVGA, audio, PCM

Chapter 2 System Setup23The various drivers and utilities in the CD-ROM disc have their owntext files which help users install the drivers and unders

FCC Class BThis equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to Part 15 of the FCC Rules.These

24PPC-123 User's Manual

Using the Panel PC• Floppy Drive• CD-ROM Drive• PCMCIA Sockets• PS/2 Mouse and Keyboard• Audio Interface• PCI/ISA Bus Expansion• Parallel Port• Serial

26PPC-123 User's Manual3.1 IntroductionThis chapter describes basic features and procedures for using thepanel PC. Topics covered include the fl

Chapter 3 Using the Panel PC273.3 CD-ROM DriveTo insert a CD-ROM disc, press the eject button of the CD-ROM drive.The yellow activity light will flas

28PPC-123 User's Manual3.4 PCMCIAPCMCIA cards are inserted and ejected in much the same way asdiskettes.To insert a PCMCIA card, align the card

Chapter 3 Using the Panel PC29Figure 3-4: Using the I/O interface (upper level ports excluding COMports)USBkeyboardPrinterNetworkPS/2mouse

30PPC-123 User's ManualFigure 3-5: Using the I/O interface (lower level ports and COM ports)MicrophoneHeadphonesCD-ROMplayerJoystickCRTmonitor

Chapter 3 Using the Panel PC313.5 PS/2 Mouse and KeyboardIf you wish to use a full-size desktop keyboard and PS/2 mouse withyour panel PC, follow the

32PPC-123 User's ManualFigure 3-6: PCI/ISA bus expansionPCI/ISAbus cardMetalplatePCI/ISAexpansionslot cover

Chapter 3 Using the Panel PC333.7 Parallel PortThe panel PC supports the latest EPP and ECP parallel port protocolsfor improved performance and versa

Additional Information and Assistance1. Visit the Advantech websites at www.advantech.com orwww.advantech.com.tw where you can find the latest informa

34PPC-123 User's Manual3.9 VGA PortAn external VGA-compatible device may be connected to the systemthrough the 15-pin external port located on t

Chapter 3 Using the Panel PC353.12 Audio InterfaceThe audio interface includes three jacks: microphone in, line out andline in. (See Fig. 3-5.) Their

36PPC-123 User's Manual3.15 Infrared ModuleThis sensor on the front panel supports the optional wireless transmit-ting and receiving of infra-re

Hardware Installationand Upgrading• Overview of Hardware Installation andUpgrading• Disassembling the Panel PC• Installing the 2.5" Hard Disk Dr

38PPC-123 User's Manual4.1 Overview of Hardware Installation andUpgradingThe panel PC consists of a PC-based computer that is housed in aplastic

Chapter 4 Hardware Installation and Upgrading39Figure 4-1: Disassembling the plastic rear cover of the panel PCPCI/ISAexpansion PCBSide panelCPU fan

40PPC-123 User's Manual4.3 Installing the 2.5" Hard Disk Drive (HDD)You can attach one enhanced Integrated Device Electronics (IDE)hard dis

Chapter 4 Hardware Installation and Upgrading414.4 Installing the Central Processing Unit(CPU)The panel PC's central processing unit (CPU) can b

42PPC-123 User's Manual8. Insert the CPU with the correct orientation. The notched corner ofthe CPU (with the white dot) should point towards th

Chapter 4 Hardware Installation and Upgrading43Figure 4-3: Installing the CPUCPU fanCPU coverHeat sink clipHeat sinkCPULeverSocket 370

Safety Instructions1. Read these safety instructions carefully.2. Keep this User's Manual for later reference.3. Disconnect this equipment from a

44PPC-123 User's Manual4.5 Installing the SDRAM Memory ModuleYou can install from 32 to 256 MB of SDRAM memory. The panelPC system provides one

Chapter 4 Hardware Installation and Upgrading454.6 Installing the Floppy Disk Drive (FDD)and Slim CD-ROM DriveInstallation of a floppy disk drive and

46PPC-123 User's Manual9. Connect the FDD cable (26-pin to 26-pin) and CD-ROM cable(40-pin to 40-pin). The other end of the FDD cable is connect

Jumper Settings and Con-nectorsThis chapter tells how to set up the panel PChardware, including instructions on settingjumpers and connecting peripher

48PPC-123 User's Manual5.1 Jumpers and Connectors5.1.1 Setting jumpersYou can configure your panel PC to match the needs of your applica-tion by

Chapter 5 Jumper Settings and Connectors495.1.2 Jumpers and switchThe motherboard of the panel PC has a number of jumpers that allowyou to configure

50PPC-123 User's Manual5.1.3 Locating jumpers and switchFigure 5-1: Locating jumpers on the PPC-123 motherboardJP5: COM2RS-232/422/485settingJP3

Chapter 5 Jumper Settings and Connectors515.1.4 ConnectorsOnboard connectors link the panel PC to external devices such as harddisk drives or floppy

52PPC-123 User's Manual5.1.5 Locating connectorsFigure 5-2: Locating connectors on the PPC-123 motherboardJ6: Internalspeaker connector(Reserved

Chapter 5 Jumper Settings and Connectors535.2 CPU InstallationYou can install an Intel Celeron™ or Pentium® III CPU without settingany frequency rat

Wichtige Sicherheishinweise1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.2. Heben Sie diese Anleitung für den späteren Gebrauch auf.3. Vor j

54PPC-123 User's Manual5.4 COM-port InterfaceThe panel PC provides four serial ports (COM1, 3, 4: RS-232; COM2:RS-232/422/485) in one COM port c

Chapter 5 Jumper Settings and Connectors55COM1 and COM2 are one set. You can exchange the address rangeand interrupt IRQ of COM1 for the address rang

56PPC-123 User's Manual5.4.3 COM3 / COM4 pin 9 output type setting (JP6)Table 5-8: COM3/COM4 pin 9 output type setting (JP6)*Normal operation +5

Chapter 5 Jumper Settings and Connectors575.6 VGA InterfaceThe panel PC's AGP VGA interface can drive conventional CRTdisplays. It is also capab

58PPC-123 User's Manual5.7 Watchdog Timer ConfigurationAn onboard watchdog timer reduces the chance of disruptions whichEMP (electromagnetic pul

PCI Bus EthernetInterfaceThis chapter provides information onEthernet configuration.• Introduction• Installation of Ethernet Driver- for Windows 95- f

60PPC-123 User's Manual6.1 IntroductionThe PPC-123 is equipped with a high performance 32-bit Ethernetchipset which is fully compliant with IEEE

Chapter 6 PCI Bus Ethernet Interface61Press the "HaveDisk..." button.4.a.2.a.Select "Start","Settings", "ControlPa

62PPC-123 User's Manual5.6.endType the path "D:\PPC123~7\LAN\W95OSR2"a.Click the "OK" button.b.a.Choose thehighlighted "

Chapter 6 PCI Bus Ethernet Interface636.2.2 Installation for Windows 982.a. Choose "Driver" folder1.a.Select "Start","Settin

ContentsChapter 1 General Information 11.1 Introduction ... 21.2 How to Use This Manual...

64PPC-123 User's Manual5.a.Click "Next"6.a.Select "NetworkAdaptors"b. Click "Next"Choose "Have Disk"7.a.

Chapter 6 PCI Bus Ethernet Interface659.a. Click "OK"10.a.Click "Next"Click "Finish"11.a.Select "Yes" to rebo

66PPC-123 User's Manual6.2.3 Installation for Windows NT1.a.Select "Start","Settings", "ControlPanel", and thendou

Chapter 6 PCI Bus Ethernet Interface675.a.4.a.Click the "OK" button.b.Choose thehighlighted"RTL8139(A/B/C/8130)PCI FastEthernet Adapte

68PPC-123 User's Manual6.3 Further InformationRealtek website: www.realtek.com.twAdvantech websites: www.advantech.comwww.advantech.com.tw

AGP SVGA Setup• Introduction• Installation of SVGA Driver- for Windows 95/98- for Windows NT- for Windows 2000- for Windows ME• Further InformationCHA

70PPC-123 User's Manual7.1 IntroductionThe PPC-123 has an onboard AGP flat panel/VGA interface. Thespecifications and features are described as

Chapter 7 PCI SVGA Setup717.2 Installation of SVGA DriverComplete the following steps to install the SVGA driver. Follow theprocedures in the flow ch

72PPC-123 User's Manual7.2.1 Installation for Windows 95/981.a. Select "Start", "Run"b.Click "OK"Type the path &qu

Chapter 7 PCI SVGA Setup731.a.Select "Start", "Run"b.Click "OK"Type the path "D:\123&153\VGA(3DM)\WinNT\Setup.

3.5 PS/2 Mouse and Keyboard ... 313.6 PCI/ISA Bus Expansion... 313.7 Parallel Po

74PPC-123 User's Manual7.2.3 Installation for Windows 20001.a.Select "Start", "Run"b.Click "OK"Type the path "

Chapter 7 PCI SVGA Setup751.a.Select "Start", "Run"b.Click "OK"Type the path "D:\123&153\VGA(3DM)\WinME\Setup.

76PPC-123 User's Manual7.3 Further InformationFor further information about the AGP SVGA installation in yourPPC-123, including driver updates,

Audio• Introduction• Installation of Audio Driver- for Windows 95/98- for Windows NT- for Windows 2000/MECHAPTER8

78PPC-123 User's Manual8.1 IntroductionThe PPC-123's onboard audio interface provides high-quality stereosound and FM music synthesis (ESFM

Chapter 8 Audio798.2.1 Installation for Windows 95/981.a.Select "Start","RUN".Enter the driverpath: "D:\PPC123&153\Audio

80PPC-123 User's Manual5.a. After installation,select "Start","Settings", "ControlPanel", "System".Click

Chapter 8 Audio818.2.2 Installation for Windows NT1.a.Select "Start","Settings", "ControlPanel".Double Click the"M

82PPC-123 User's Manual5.a.Slecte thehighlighted item.6.a.Press the "RestartNow" buttom toreboot yourcomputer.b.Press the "OK&quo

Award BIOS SetupThis chapter describes how to set BIOSconfiguration data.CHAPTER9