Advantech PPC-140 Manual de usuario Pagina 168
- Pagina / 194
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
150
PPC-120/140 User’s Manual
7. Unscrew the four screws on the power supply board. The power
supply board can be detached from the LCD holding plate after
unplugging the two cables from the power inlet and motherboard.
8. Detach the LCD holding plate and LCD by unscrewing the four screws
at the bottom. The LCD inverter can also be detached by unscrewing
the three screws at the bottom.
9. Detach the cables of the LCD, touchscreen, LCD inverter and speaker
from the holes of the holding plate.
10. Detach the touchscreen by removing it from the the LCD. The rubber
pad around the touchscreen and glass can also be detached.
11. The speakers are located on the two sides of the front cover.
- PPC-120/140 1
- Copyright Notice 2
- FCC Class B 3
- Packing List 4
- Safety Instructions 6
- Wichtige Sicherheishinweise 7
- Contents 8
- Appendices 13
- General Information 19
- 1.1 Introduction 20
- 1.2 How to Use This Manual 22
- 1.3 Specifications 24
- PCI SVGA/flat panel interface 25
- Audio function 25
- PCI bus Ethernet interface 26
- Touchscreen (optional) 26
- Optional modules 27
- Environment 27
- 1.4 Dimensions 28
- System Setup 29
- Infrared 30
- Fig. 2-2 31
- Main power switch 33
- AC inlet 33
- 2.3 Installation Procedures 34
- 2.3.3 Switching on the power 35
- 2.6 Installing the Drivers 37
- Using the Panel PC 39
- 3.1 Introduction 40
- 3.2 Floppy Drive 40
- 3.3 CD-ROM Drive 41
- 3.4 PCMCIA 42
- Chapter 3 43
- 3.5 PS/2 Mouse and Keyboard 45
- 3.6 PCI/ISA Bus Expansion 45
- 3.7 Parallel Port 47
- 3.8 Serial COM Ports 47
- 3.9 VGA Port 48
- 3.10 Game Port 48
- 3.11 USB Ports 48
- 3.12 Audio Interface 49
- 3.13 Ethernet 49
- 3.15 Infrared Module 50
- 3.16 Touchscreen (Optional) 50
- Hardware Installation 51
- Upgrading 52
- Metal plate 55
- 2.5" HDD 55
- DIMM socket 58
- 3.5" floppy drive 59
- Jumper Settings and 61
- Connectors 61
- 5.1 Jumpers and Connectors 62
- 5.1.2 Jumpers 63
- 5.1.3 Locating jumpers 64
- 5.1.4 Connectors 65
- 5.1.5 Locating connectors 66
- PCI clock 69
- * CPUCLK/2 69
- P55C P54C 72
- 3.5x 1.5x 72
- 2.5x 2.5x 72
- * default setting 74
- 5.2.6 Reset system (JP16) 75
- 5.3 COM-port Interface 76
- 5.4 VGA Interface 78
- 5.4.2 Panel type select (JP9) 79
- * System reset IRQ11 81
- PCI Bus Ethernet 83
- Interface 83
- 6.1 Introduction 84
- 6.3 Further Information 90
- PCI SVGA Setup 91
- 7.1 Introduction 92
- D:\VGA\Win31\Setup.exe 94
- ChipsCPL 95
- D:\VGA\Win95\ 96
- D:\VGA\NT40\ 100
- Chapter 7 PCI SVGA Setup 101
- 7.2.4 Installation for OS/2 102
- 7.3 Further Information 104
- 8.1 Introduction 106
- Chapter 8 Audio 107
- D:\Audio\win31\setup.exe 109
- D:\Audio\win95 111
- Award BIOS Setup 115
- 9.1 Award BIOS Setup 116
- 9.2 CMOS Setup Utility 116
- 9.3 Standard CMOS Setup 117
- 9.4 BIOS Features Setup 119
- Chapter 9 Award BIOS Setup 121
- 9.5 Chipset Features Setup 122
- 9.6 Power Management Setup 123
- HDD Ports Activity 126
- VGA Activity 126
- IRQ# Activity 126
- Resources Controlled By 127
- 9.8 Load BIOS Defaults 129
- 9.9 Load Setup Defaults 129
- 9.10 Integrated Peripherals 130
- IDE Burst Mode 131
- IDE HDD Block Mode 131
- Onboard FDD Controller 131
- 9.11 Password Setting 133
- 9.12 IDE HDD Auto Detection 134
- 9.13 Save and Exit Setup 135
- 9.14 Exit Without Saving 135
- Touchscreen 137
- 10.1 Introduction 138
- Chapter 10 Touchscreen 139
- BEFORE YOU BEGIN 152
- STEP 2 - COPY THE SOFTWARE 153
- STEP 3 - MODIFY CONFIG.SYS 154
- No Mouse 155
- Disabling the COM Drivers 155
- LCD Specifications and 157
- Selection Settings 157
- PPC-140T PPC-140S PPC-120T 158
- Programming the 159
- Watchdog Timer 159
- Full Disassembly 163
- Procedures 163
- PPC-120/140 User’s Manual 164
- Pin Assignments 171
- IR Connector (J1) 172
- Appendix D Pin Assignments 173
- Internal COM4 Connector (J4) 174
- Pin Signal 175
- Sandisk SSD Connector (J6) 176
- # Low active 177
- Floppy Drive Connector (J8) 178
- CD-ROM Connector (J9) 179
- CPU Fan Power Connector (J10) 179
- Fan Power Connector (J12) 185
- AT Power Connector (J13) 185
- Mounting Instructions 189
- E.1 Introduction 190
- E.2 Panel Mounting 190
- Figure E-2: Panel mounting 191
- Fixation wedge 191
- Plastic cap 191
- Rubber pad 191
- E.3 Desktop Stand Mounting 192
- E.4 Swingarm Stand Mounting 194
© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales